Implementation of Load cell Sensors as Monitoring the Weight of Infusion Fluids in Inpatients Based on Internet of Things (IoT)
Implementasi Sensor Load cell Sebagai Pemantau Berat Cairan Infus Pada Pasien Rawat Inap Berbasis Internet of Things (IoT)
-
(1) * Vila Puspita Devi Vila
Universitas Hang Tuah Surabaya
Indonesia
(2) Muh. Taufiqurrohman Universitas Hang Tuah Surabaya
Indonesia
(3) Joko Subur Universitas Hang Tuah Surabaya
Indonesia
(*) Corresponding Author
Abstract
The use of electronics for medical purposes is currently very much needed, especially for monitoring infusion fluids. Infusion plays an important role in supporting the needs of inpatients as medicine, vitamins or replacing the patient's body fluids. One problem that often arises is the delay in replacing infusion fluid bags that have run out. If the infusion fluid runs out and the replacement is late, blood from the vein can enter the infusion tube, as well as air bubbles entering the vein. This condition can be fatal because blood flow is disrupted, and the oxygen the body needs cannot be distributed through the blood, so the body's organs will lack oxygen. Currently it is still controlled manually, so with research on an infusion monitoring system using a Load cell sensor which can be monitored remotely, it makes the nurse's time more efficient. In this research, the results of tests that have been carried out regarding load cell sensor readings have a 100% success rate in detecting the weight of infusion fluid from full condition until the fluid is considered finished and the data can be sent in real-time to Android by utilizing Internet of Things (IoT) technology.
References
D. Nataliana, N. Taryana, And E. Riandita, “Alat Monitoring Infus Set Pada Pasien Rawat Inap Berbasis Mikrokontroler Atmega 8535,” Elkomika J. Tek. Energi Elektr. Tek. Telekomun. Tek. Elektron., Vol. 4, No. 1, P. 1, 2018. DOI: https://doi.org/10.26760/elkomika.v4i1.1
N. Y. Handayani Et Al., “Faktor Yang Berhubungan Dengan Kepatuhan Perawat,” J. Ilmu Keperawatan Dan Kebidanan Vol.11, Vol. 11, No. 2, Pp. 328–334, 2020. DOI: https://doi.org/10.26751/jikk.v11i2.663
K. N. T. Yayer, W. A. Weliamto, R. Sitepu, And H. Pranjoto, “Monitoring Dan Penghentian Cairan Infus Menggunakan Timbangan Infus Digital Dengan Memanfaatkan Web Server,” Simetris J. Tek. Mesin, Elektro Dan Ilmu Komput., Vol. 11, No. 1, Pp. 55–64, 2020. DOI: https://doi.org/10.24176/simet.v11i1.3601
T. Akbar And I. Gunawan, “Prototype Sistem Monitoring Infus Berbasis Iot (Internet Of Things),” Edumatic J. Pendidik. Inform., Vol. 4, No. 2, Pp. 155–163, 2020. DOI: https://doi.org/10.29408/edumatic.v4i2.2686
I. Rohman And M.Taufiqurrohman, “Monitoring Ketinggian Air Pada Bengawan Solo Berbasis Mikrokontroller Dan Komunikasi Wifi,” J. Semin. Nas. Kelaut. Xii, Pp. 102–107, 2017.
R. C. Yustihan And M. Taufiqurrohman, “Rancang Bangun Sistem Monitoring Dissolved Oxygen Dan Power Of Hydrogen Pada Air Tambak Budidaya Udang Vaname Berbasis Internet Of Things,” J. Borneo Inform. Dan Tek. Komput., Vol. 3, No. 2, Pp. 34–44, 2023. DOI: https://doi.org/10.35334/jbit.v3i2.4246
M. B. Zaman And M. Taufiqurrohman, “Rancang Bangun Sistem Kontrol Dan Pemantau Rov (Remotely Operated Vehicles) Berbasis Android,” Jurnal Teknik Elektro Dan Komputer Triac, Vol. 5, No. 1. 2018. DOI: https://doi.org/10.21107/triac.v5i1.3833
Agus Wibowo And Lawrence Adi Supriyono, “Analisis Pemakaian Sensor Loadcell Dalam Perhitungan Berat Benda Padat Dan Cair Berbasis Microcontroller,” Elkom J. Elektron. Dan Komput., Vol. 12, No. 1, Pp. 1–5, 2019. DOI: https://doi.org/10.51903/elkom.v12i1.102
A. P. Manullang, Y. Saragih, And R. Hidayat, “Implementasi Nodemcu Esp8266 Dalam Rancang Bangun Sistem Keamanan Sepeda Motor Berbasis Iot,” Jire (Jurnal Inform. Rekayasa Elektron. , Vol. 4, No. 2, Pp. 163–170, 2021, [Online].
R. Mardiati, F. Ashadi, And G. F. Sugihara, “Rancang Bangun Prototipe Sistem Peringatan Jarak Aman Pada Kendaraan Roda Empat Berbasis Mikrokontroler Atmega32,” Telka - Telekomun. Elektron. Komputasi Dan Kontrol, Vol. 2, No. 1, Pp. 53–61, 2016. DOI: https://doi.org/10.15575/telka.v2n1.53-61
L. Aditya And D. Riska, “Rancang Bangun Alat Pengukur Kadar Oksigen Non Invasive Menggunakan Sensor Max30100,” Https://Medium.Com/, Vol. 4, No. 3, Pp. 248–253, 2020, [Online].
A.F Shinta, “Rancang Bangun Sistem Monitoring Volume Dan Laju Tetes Infus Pasien Menggunakan NODEMCU ESP8266”, [Skripsi], Pendidikan Teknik Elektro Jurusan Teknik Elektro Fakultas Teknik Universitas Negeri Semarang, 2020.
Muthmainnah, H.Mansur, N. Chamidah, “Desain dan Pengembangan Monitoring Cairan InfusBerbasis Internet of Things (IoT) Telegram”, Jurnal Pendidikan MIPA, Hal. 812-817, Vol. 13, No. 3. 2023 DOI: https://doi.org/10.37630/jpm.v13i3.1178
Copyright (c) 2025 Vila Puspita Devi Vila, Muh. Taufiqurrohman, Joko Subur
This work is licensed under a Creative Commons Attribution 4.0 International License.
